Buick Regal Used Engines

Used Buick Regal engines covering 1990 to 2004 and 2011 to 2019. The Regal was not sold in the US between those two runs, and nothing crosses the gap. Every engine is listed as tested and ready to install, ships with a written warranty, and ships free anywhere in the lower 48.

If your Regal is from 1990 to 1996: reading 6-231 and 6-191

Listings from these years use the older cubic-inch naming rather than litres. 6-231 means a six-cylinder of 231 cubic inches, which is the 3.8. 6-191 means 191 cubic inches, which is the 3.1. They are not model codes or valve counts — just the displacement written the way it was written at the time.

The 8th VIN character then settles it: the 3.8 is VIN L through 1995 and VIN K for 1996; the 3.1 is VIN T on the earlier cars and VIN M from 1994.

Two splits in this era you will not find on a spec sheet

  • 1994 and 1995, 3.1 VIN M — the block itself differs. On some the upper-centre air-conditioning mounting is drilled and tapped and on others it is not. Our listings are split on this. Look at your own block before ordering: if your car's bracket bolts there and the replacement block has no thread, the engine will not mount.
  • 1993, 3.1 VIN T — one listing is specifically without a camshaft sensor. Check whether yours has one.

1997 to 2004: supercharged or not

This is the single most important question on a late-nineties or early-two-thousands Regal, and the VIN answers it directly on the 3.8:

  • VIN K — the naturally aspirated 3.8
  • VIN 1 — the supercharged 3.8, which is the Regal GS

These are not interchangeable. The 3.1, where fitted, is VIN J. For 2000 the 3.1 splits again on emissions: Federal, option NF2 against California, option NC1.

2011 to 2019: three different 2.4s and two different 2.0s

The modern Regal is where displacement becomes genuinely useless on its own. Over these years there were three distinct 2.4 engines and two distinct 2.0 engines, and you need the RPO code:

  • 2.4, VIN C, opt LAF — 2011 only
  • 2.4, VIN K, opt LEA — 2012 to 2017
  • 2.4, VIN R, opt LUK, eAssist — the mild hybrid, 2012 to 2016. If your car is an eAssist, a plain 2.4 is the wrong engine.
  • 2.0, VIN V, opt LHU — 2011 to 2013
  • 2.0, VIN X, opt LTG — 2014 to 2019, and these split by front- or all-wheel drive

Emissions splits on the 2.4

Through 2015, nearly every 2.4 listing divides on emissions: Federal, option NT7 against California, options NU1, NU5 and NU6. The code is on the glovebox or door-jamb sticker. A Federal engine in a California-certified car is the wrong part.

2011 also splits mid-production

For 2011 the 2.4 VIN C changes part-way through the build run, at a specific vehicle number: listings are split through VIN B1014159 and from VIN B1014160, read from the last eight characters of the VIN. Two cars of the same model year, same engine code and same emissions package can still need different engines depending on which side of that number they fall.

What we need from you

The VIN covers almost all of this in one go — the 8th character gives the engine and, on a 2011 car, the last eight give the build position. Beyond that: on a 1994 or 1995 3.1, whether your block's upper-centre AC mounting is drilled and tapped; and on any 2.4 to 2015, the emissions code from the sticker. Send the VIN and we read it and confirm against your vehicle before anything ships.

Related

Replacing the transmission instead or as well: Buick Regal used transmissions, where the supercharged split and the RPO codes apply again. Everything we list for the make: Buick used engines. Or browse used engines by model.